-
Choose your length and width
The FLOATING SHELF BRACKET's we make at Welds & Wood are designed to be strong and easy for DIY install.
Made from solid steel flat bar and rod, we have a range of lengths and depths to suit your floating shelf. At 35mm wide, the 4mm flat bar has been laser cut with a number of slots so you can choose where to screw to your wall. Useful to find a stud as you are not restricted to just a few holes like other brackets on the market.
We started making these as we found the current range in the market didn't fit our purpose. Our brackets are custom designed for our range of floating shelves, however these are perfect for anyone looking to hang their own shelves.Drill DIA 12.5mm (12.7mm or 1/2inch is actually perfect if you have one though) holes in your shelf to match the rod spacings.
We cut them, weld them and clean them. Then we wipe on a rust preventative lubricant.
PLEASE NOTE:
We make these for our own floating shelves, and make then strong. If you are worried about imperfections such as the natural colour of steel, visible welds at the rear of the pegs, not powder coated etc. then these are probably not for you. But they work, and they work really well..
-
LENGTHS
Click here to see our SELECTION GUIDE
20cm + 2 Peg
30cm + 2 Pegs
50cm + 2 Peg
70cm + 2 Peg
70cm + 3 Peg
90cm + 2 Peg
90cm + 3 Peg
110cm + 2 Peg
110cm + 3 Peg
130cm + 3 Peg
130cm + 4 Peg
160cm + 6 Pegs
190cm + 7 pegs
*read Weight Capacity section for more details.
DEPTHS of ROD10cm | 15cm | 20cm
WIDTH of flat bar base | 3.5cm
THICKNESS of flat bar base | 4mm
DIAMETER of pegs | 12mmm -
Floating Shelf Bracket:
Brackets are ready to be levelled and screwed directly to a flat wall.
Please see our Installation guide below for details on fixings and anchors to mount our shelves.
If you require specific anchors for your particular wall type, UPGRADED FIXINGS PACKS are available here.
Each pack has 6 anchors / fixings designed for your particular wall type.
1 PACK (6 ANCHORS) WILL BE ENOUGH FOR MOST of our WALL MOUNTED PRODUCTS AND FLOATING SHELVES UNDER 1.5m.
LONGER SHELVES REQUIRE 2 PACKS (12 ANCHORS)
Weight Capacity:
Load ratings vary for each situation. Please refer to this guide for more info
Installation:
We recommend a qualified installer to install our brackets, however, any handy person should be able to install using our instructions provided here.
If no masonry or timber studs are available, it’s up to your discretion whether or not your wall will be able to handle the weight. If using only plasterboard wall plugs and screws, maximum weight will depend on the wall plugs you have used, the condition of your wall, and whether the wall plug has been installed correctly.
Welds and Wood accept no responsibility for the failed installation of your bracket.
*When installed using our install methods. Instructions are available in our here
-
Click here for weight ratings
Not intended for shelves wider than 35cm wide.
-
Our products are made to order.
Click here to find Current Production Times
Longer production times can occur in peak buying periods.
We ship Australia wide and times are calculated in business days, and begin after we have made, packaged and sent your order. Shipping times can vary depending on carrier delays, time of year etc.
Shipping to Perth - 1 day
Shipping to all other Capital Cities and most regional towns - 5 - 8 days
Shipping to remote or regional areas - Up to 2 weeks
-
As our products are made to order, we only accept cancellations of orders or changes of mind within 24 hours of purchase. Please choose carefully.
Click here for our returns, warranty and changes section
-
Please read our safety guide prior to installation
